Fabrication of superhydrophobic-superoleophilic membranes for oil-water separation applications

Rasouli, S. Abbas (2021) Fabrication of superhydrophobic-superoleophilic membranes for oil-water separation applications. Masters thesis, Memorial University of Newfoundland.

[img] [English] PDF - Accepted Version
Available under License - The author retains copyright ownership and moral rights in this thesis. Neither the thesis nor substantial extracts from it may be printed or otherwise reproduced without the author's permission.

Download (4MB)

Abstract

The increasing volume of industrial oily wastewater and recent oil spill incidents have negatively affected the ecosystem and human health. Accordingly, it has been a worldwide challenge to separate the water or oil from such oily wastewater effectively. Recently, owing to the low efficiency of conventional techniques, a great interest has been paid in using membranes with engineered wettability especially superhydrophobic-superoleophilic (SHSO) ones, for oil-water separation applications. In this research, the SHSO mesh is fabricated to examine the effectiveness of membrane surface modification for oil-water separation purposes. After cleaning and activating the stainless-steel mesh by piranha solution, two different silanes with short- and long-alkyl functional chains (Dynasylan® Sivo 408 and Dynasylan® F8261, respectively) are used to modify the mesh surface via a dip-coating technique. Functionalized silica micro and nanoparticles with different ratios are tried to evaluate their potential as morphology modifiers. The superhydrophobic and superoleophilic membranes are then characterized by the contact angle, sliding angle, scanning electron microscopy (SEM), energy dispersive X-ray (EDX), Fourier transform infrared spectroscopy (FTIR), Transmission Electron Microscopy (TEM), and X-ray Powder Diffraction (XRD) techniques. Utilization of Dynasylan® F8261 as a coating solution leads to a higher water contact angle (WCA) due to having a longer alkyl functional chain, compared to Dynasylan® Sivo 408. Moreover, the combination of micro (25%) and nano (75%) particles results in the highest WCA (165.8˚), followed by the scenario of only nanoparticles with a WCA of 163.8˚. The coating solution with only nanoparticles is thus proposed as the optimal case, since the microparticles tend to settle, making the solution non-homogeneous based on the SEM results. Analysis of characterization tests confirms that the as-prepared mesh exhibits SHSO properties. The stability analysis is also conducted by submerging the SHSO membranes into solutions of NaCl (1M), H₂SO₄ (0.1M), and NaOH (0.1M). Except for the NaOH solution, this mesh maintains its SHSO properties in the solutions of NaCl and H₂SO₄ over one-month stability assessment. The results of static oil-water separation show a higher separation efficiency for hexane (99%) than canola oil (97%), owing to the lower viscosity of hexane. The dynamic oil-water separation tests are also performed using coated mesh tubes in a cross-flow gravity-based separator. The oil-water mixture is pumped into the tube side for 70 minutes. The oil-water mixture level is adjusted to avoid the breakthrough of the water phase into the SHSO membrane. The effluents of oil and water from the system are directed to the secondary separators to analyze the oil and water separation efficiency. Different oil concentrations (10, 30, and 50 vol%) and total flow rates (5, 10, and 15 mL/min) are examined to evaluate the performance of the SHSO mesh in separating oil from the oil-water mixture. The maximum oil separation efficiency of 97% is obtained from a scenario with 10 vol% oil and 5 mL/min total flow rate. Conversely, the minimum oil separation efficiency (86%) occurs for the case with a 15 mL/min total flow rate and 50 vol% oil. The water separation efficiency is not affected by changing oil-water mixture characteristics, as it reached the maximum level (100%) shortly. The flower-like silica nano-roughness on the SHSO mesh tube by decreasing the pore size from around 80 to 45 μm effectively prohibits the water phase from entering the mesh pores up to 3 cm H₂O column. By increasing the oil permeate flow rates from 0.5 to 7.5 ml/min, the oil permeation flux increases from 314 to 790 (L/m².h). By the time, the production rate of oil and water shows a linear behaviour indicating that the SHSO coated mesh does not experience the fouling phenomenon. Both separated phases are very clear. Therefore, the proposed methodology can have practical applications in oil removal from oily wastewater and oil spill incidents.

Item Type: Thesis (Masters)
URI: http://research.library.mun.ca/id/eprint/14939
Item ID: 14939
Additional Information: Includes bibliographical references.
Keywords: Superhydrophobic-superoleophilic, Mesh-based membrane, Fabrication methods, Characterization techniques, Oil-water separation
Department(s): Engineering and Applied Science, Faculty of
Date: February 2021
Date Type: Submission
Digital Object Identifier (DOI): https://doi.org/10.48336/vs9r-5k42
Library of Congress Subject Heading: Oil separators--Design and construction; Hydrophobic surfaces; Membranes (Technology).

Actions (login required)

View Item View Item

Downloads

Downloads per month over the past year

View more statistics